Siirry sisältöön

RANE B22IM

Balance Buddy

Tuote ei ole tilattavissa
Hinta puuttuu /kpl
Tuoteno: 943759

Tuotetiedot


RANE BB22 – UNBALANCED TO BALANCED CONVERTER

The Rane BB22 Balance Buddy is a handy professional-grade tool used to provide isolation for, and conversion of, unbalanced -10 dBV consumer level RCA outputs up to balanced +4 dBu professional XLR inputs. The BB22 converts one pair from -10 dBV to +4 dBu. There are two male XLR connectors and two RCA jacks.

Unbalanced lines should always be kept under 10 feet (3 meters) to prevent undesirable effects such as hum and noise. The BB22 allows conversion to balanced lines that can be run across a studio or an installation without loss of signal quality. For instance, a BB22 may be mounted to the back of a jukebox converting its unbalanced outputs to balanced lines, feeding an amplifier in another room.

Signal-to-noise performance is perfectly preserved using the BB22, since it uses only passive transformers to convert signal levels. It adds no additional noise whatsoever. Use of professional quality nickel core (“80” Ni) transformers guarantee low distortion, wide bandwidth and high signal level handling capability.

The BB22’s isolation transformers provide a quick and affordable answer to most jobs requiring signal level conversion and output balancing.

BB22 Features
  • Convert unbalanced signals to balanced.
  • Isolate lines to stop ground loops.
  • Enables the use of long balanced cables for a hum-free signal.
  • 2 channels of -10 dBV (RCA) to +4 dBu (XLR) conversion
  • +24 dBu maximum levels
  • Nickel core “80” Ni Transformers provide wide bandwidth and low distortion
  • BB22 Applications
    Conversion Ratio

    The casual observer would think to convert -10 dBV to +4 dBu, you would need 14 dB of gain. The casual observer would be wrong. You only need 12 dB of gain. The reason is not only do you change levels; you also change reference levels - from dBV to dBu. The first (dBV) references everything to 1.0 volt, while the second (dBu) references everything to 0.775 volts (this comes from the old power reference of 0 dBm, which equaled 1mW into 600 Ω, which equaled .775 volts).

    Driving Impedances

    Some people wrongly feel you cannot use a transformer to convert between -10 dBV and +4 dBu because of low impedances. This is not a problem as long as you use them to interconnect equipment with at least 15k ohms input impedance. Since most professional products have input impedances of 20 kΩ or greater (50k and 100 kΩ are not uncommon), this should never be difficult. A 15 kΩ load winds up looking like 1 kΩ to the equipment with the -10 dBV output (due to transformer action). This may seem excessively low, but is not in practice. The maximum transformer output level of +24 dBu occurs with an input level of +10 dBV, which equals 3.16 volts. And 3.16 volts driving 1 kΩ only requires 3.16 milliamps, which is a very modest requirement for any -10 dBV equipment to deliver.

    Wiring

    The BB22 follows AES/ANSI/IEC standards of pin 2 positive and pin 3 negative. Note the shields (commons) of the RCA jacks are not tied together. This provides better ground isolation of the unbalanced units. A positive signal applied to the tip of the RCA jack causes a positive signal to appear on pin 2 of the XLR, and vice-versa if signal direction is reversed.

Ladattavat

logotypes-fi.png
 

 

Tuote on siirretty ostoskoriin